ATMEL-ICE PCBA KIT,ATATMEL-ICE-PCBA

  • RS-stocknr. 130-6124
  • Fabrikantnummer ATATMEL-ICE-PCBA
  • Fabrikant Microchip
Datasheets
Wetgeving en compliance
Conform
Productomschrijving

ATATMEL-ICE PCBA

The Atmel-ICE series consists of development tools for debugging and programming ARM Cortex-M based Atmel SAM and Atmel AVR microcontrollers with on-chip debug capability. The Atmel-ICE series supports JTAG, SWD, PDI, TPI, aWire, SPI and debugWIRE interfaces and is compatible with Atmel Studio.

Kit Contains:

Atmel-ICE unit without plastic encapsulation130-6122 Full Kit available130-6123 Basic Kit available

System Requirements

The Atmel-ICE unit requires that a front-end debugging environment Atmel Studio version 6.2 or later is installed on your computer. The Atmel-ICE should be connected to the host computer using the USB cable provided, or a certified Micro-USB cable.

How to turn the Atmel - ICE on?The Atmel-ICE is powered by the USB bus voltage. It requires less than 100mA to operate, and can, therefore, be powered through a USB hub. The power LED will illuminate when the unit is plugged in. When not connected in an active programming or debugging session, the unit will enter low-power consumption mode to preserve your computer's battery. The Atmel-ICE cannot be powered down - it should be unplugged when not in use. How does it connect?The Atmel-ICE communicates primarily using a standard HID interface and does not require a special driver on the host computer. The Atmel-ICE must be connected to an available USB port on the host computer using the USB cable provided, or suitable USB certified micro cable. The Atmel-ICE contains a USB 2.0 compliant controller and can operate in both full-speed and high-speed modes. For best results, connect the Atmel-ICE directly to a USB 2.0 compliant high-speed hub on the host computer using the cable provided.

Kit Types:

Cable kit: 177-9591Adapter kit: 177-9590Basic kit: 130-6123PCBA kit: 130-6124Full kit: 130-6122

Tijdelijk niet op voorraad – nieuwe voorraad verwacht op 11-08-2020, met een levertijd van 1 werkdag.
Prijs Each
56,76
(excl. BTW)
68,68
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 56,76
Related Products
The CCS LOAD-n-GO is a hand-held mobile In-Circuit ...
Description:
The CCS LOAD-n-GO is a hand-held mobile In-Circuit Serial Programmer (ICSP) that offers a quick and easy 2-step solution for the in-the-field programming of PIC Microcontrollers. The device can store up to four separate firmware images or programs utilising 2 ...
Flasher Portable PLUS has been designed to fill ...
Description:
Flasher Portable PLUS has been designed to fill the need for a portable, battery-operated production-grade Flash memory programmer used for in-field firmware updates. Initial setup/preparation for stand-alone mode operation is done via the J-Flash software. It supports storage of multiple ...
The PIC-01 allows you to program Microchip serial ...
Description:
The PIC-01 allows you to program Microchip serial PIC microcontrollers, (PIC12Cxxx, PIC12CExxx, PIC12Fxxx, PIC16Cxxx, PIC16CExxx, PIC16Fxxx, and PIC18Fxxxx families), as well as serial EEPROMs Series, (24Cxx family).Equipped with 5 tulip sockets, supports components in DIP packages of 8, 18, 28 ...
This USB-based emulator provides an easy, portable, non-intrusive, ...
Description:
This USB-based emulator provides an easy, portable, non-intrusive, target-based debugging solution for Analog Devices JTAG processors and DSPs. It performs a wide range of emulation functions, including single-step and full speed execution with pre-defined breakpoints, and viewing and/or altering of ...