Texas Instruments USB Adapter Board - USB-TO-GPIO

Datasheets
Wetgeving en compliance
Conform
Productomschrijving

USB Interface Adapter Evaluation Module

Texas Instruments USB-TO-GPIO USB Interface Adapter Evaluation Module serves as an interface adapter or a bridge between a host PC (IBM™ compatible) and one or multiple slave devices via a standard type-A to mini-B USB cable. The communication between the USB interface adapter and the host PC is via USB, while the communication between the USB interface adapter and the slave device(s) is via an inter-integrated circuit (I²C), SMBus, PMBus and/or general-purpose inputs/outputs GPIOs. The bridge converts communication transactions between the USB and serial protocol.

Supports master mode I²C, SMBus or PMBus as well as GPIO.
Supports USB1.1 full speed at 12 Mbit/s. The USB interface adapter is recognized by the host as a generic human interface device (HID), so no proprietary USB or HID driver is needed. Therefore, the USB interface adapter can be treated as a USB plug-and-play device.
Selects different clock speeds (either 100 kHz or 400 kHz) for I²C, PMBus, or SMBus communications.
Configures different pullup resistors for clock, data and ALERT signals (including open-drain).
Supports flexible I²C read or write transactions (specify raw data, instead of device address, command, etc.) .
Includes .NET DLL for supporting Windows .NET GUIs using the adapter.
No Windows dependencies other than the Microsoft .NET Framework version 2.0

The IEEE 1149.1 standard test access port and boundary-scan architecture uses devices known by the JTAG acronym, from Joint Test Action Group, and is used for testing and debugging system ports and PCB assemblies. Most embedded systems employ JTAG ports to enable in-circuit debugging and firmware programming, in addition to boundary scan testing.

Specificaties
Kenmerk Waarde
Kit Classification Development Kit
Tijdelijk niet op voorraad – nieuwe voorraad verwacht op 07-09-2021, met een levertijd van 1 werkdag.
Prijs Each
132,28
(excl. BTW)
160,06
(incl. BTW)
Aantal stuks
Per stuk
1 - 1
€ 132,28
2 - 3
€ 128,89
4 +
€ 125,66
Related Products
The Microchip RN2903 LoRa® Mote is a LoRaWAN™ ...
Description:
The Microchip RN2903 LoRa® Mote is a LoRaWAN™ Class A end-device based on the RN2903 LoRa® modem module. The board provides a quick and easy to use platform for demonstrating the capabilities of the RN2903.The LoRa®Mote is battery powered, providing ...
This evaluation board serves as an aid in ...
Description:
This evaluation board serves as an aid in evaluating circuit protection on RS-485 serial device port solutions using Bourns® TBU® High-Speed Protectors (HSPs), Metal Oxide Varistors (MOVs) and Transient Voltage Suppressor (TVS) products designed to meet the required industry standards ...
The MikroElektronika RS232 2 click board performs full ...
Description:
The MikroElektronika RS232 2 click board performs full RS232 to Universal Asynchronous Receiver-Transmitter (UART) signal conversion. The MIKROE-2897 click features an On-board Surface Mount Device (SMD) jumper that allows selection of power supply voltage between 3.3V and 5V. This click ...
The UMFT240XA is a development module that converts ...
Description:
The UMFT240XA is a development module that converts USB to serial 8-Bit 245 FIFO data interfaceAsynchronous and Synchronous bit bang interface modes are availableSmall PCB assembly module designed to fit a standard 7.62mm (0.3”) wide 24-pin DIP socketOn board USB ...