Omron, LCD, Digital Counter, 24 V dc

  • RS-stocknr. 163-5152
  • Fabrikantnummer H8PS-8BP
  • Fabrikant Omron
Wetgeving en compliance

H8PS series electronic cam programmers

Easy to adjust using single function keys.
Easy replacement of mechanical cam programmers.
Number of outputs 8, 16 or 32.
Coder rotation direction change possible and easy correction at the start point.
Backlit liquid crystal display.

Solid Shaft / Hollow Shaft Absolute Encoders

An absolute encoder provides the ability to remember the exact position following any power interruption. There is also no need for synchronisation. This is one of the reasons why absolute encoders are used where a safety standard is required (i.e. robotics industry). Typical applications are for speed or position control circuits. The features for these encoders are:

+ A unique signal for each angular position
No need for initialisation (zero reference)
Immediately after power up or after an interruption of power the position is maintained
No need for a counter to process the signal

The electrical signal of the absolute encoder is directly related to the angle of the shaft. The mechanical angular position is sensed by non contact optical elements, therefore without wear. The output of an infrared diode is transmitted through a transparent code disc and a diaphragm. The light/dark pattern is converted to an electrical signal by an array of photo diodes. The same code occurs only once per revolution. This encoder is defined as a single turn encoder.

Output circuit

Types of Code
Any electronic code is made out of a combination of bits. Each bit is characterised by a Low (0) or a High (1) signal. The combination of a series of bits is called a binary word. Several binary words make a code.

Single Step Code - Only one bit on the parallel output changes state at any given time. There is no possibility of any concurrent state changes. Single step code is very versatile and can maintain accuracy even allowing for slight misalignments of the disc and scanning device
Gray Code - This is a single step code, most absolute encoders use this code
Multiple Step Codes - Natural binary code: This type of code is similar to the decimal system, except that there are only 1 and 0. Each bit, depending on its position in the binary word, has a definite value. 20 to 2n assigned

Kenmerk Waarde
Supply Voltage 24 V dc
Count Mode Hours
Display Type LCD
Input Type Logic
Mounting Type Flush Mount
Output / Interface Relay
Digit Height 11 mm
Minimum Operating Temperature -10°C
Maximum Operating Temperature +55°C
Series H8PS
Weight 300g
5 op voorraad - levertijd is 1 werkdag(en).
Prijs Each
(excl. BTW)
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 569,00
Related Products
6-digit electro-mechanical totalising counters.Counting speed for pulse / ...
6-digit electro-mechanical totalising counters.Counting speed for pulse / pause ratio = 1:- 20 pulses / sec. in Vdc minimum duration 25 ms / max. unlimited- 10 pulses / sec. in Vac minimum duration 50 ms/max. unlimited.Supplied with plug-in solder clips.Screw ...
5-digit LED displayOperating mode, start count, scaling factor ...
5-digit LED displayOperating mode, start count, scaling factor programmableSPCO relay outputTime meter with four time rangesTime relay with operation and release delayPogrammable as a time counterPlug-in screw terminal connection.
Programmable with microprocessors, comprising a general totaliser, a ...
Programmable with microprocessors, comprising a general totaliser, a counter with 2 presets, single preset counter programmable as a tachometer, & an hour meterprogrammable scaling and reset modesLED DisplayProgrammable zero shift and permanent display of the programmed parameterOperating temperature 0 to ...
Counts down pulses from a pre-set value and ...
Counts down pulses from a pre-set value and triggers a changeover contact on reaching zeroContacts return to original position when counter is reset to zeroElectrical connection via supplied plug in clipsOffers IP40 protection with cover (sold seperately)SPDT contact rated to ...