Keysight Technologies N2893A Current Probe & Clamp

Datasheets
Wetgeving en compliance
Conform
Land van herkomst: MY
Productomschrijving

Keysight N2893A AC/DC Current Probe

Wide bandwidth current probe offering flat frequency response across its entire dc to 100MHz bandwidth, low noise (< -2.5mArms) and low circuit insertion loss. The N2893A uniquely provides auto demagnetization and offset elimination features when used in conjunction with InfiniiVision or Infiniium oscilloscopes.

Hybrid technology to measure ac and dc
Compatible with 1MΩ oscilloscope input
DC supply voltage requirement of±12Vdc ±1V
Probe power consumption increases with measured current (e.g. 3VA when measuring 15A)
Maximum continuous current 15A
Maximum peak current 50A

Keysight Technologies Current Probe & Clamp

The Keysight Technologies 100MHz bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes. The probe features flat bandwidth (DC-100MHz), low noise (<2.5 mA RMS) and low circuit insertion loss. Auto demagnetization (degauss) and calibration removes any residual magnetism and unwanted DC offset in the probe. The probe is directly powered by the InfiniiVision and Infiniium Autoprobe interface, eliminating the need for an additional power supply. It is ideal for capturing transient current signals such as those found in motor controllers, switching power supplies, inverters, and current amplifiers driving inductive loads.

Features and Benefits

• Wide bandwidth from DC to 100MHz
• High S/N ratio
• Low current measurement capability
• 15A peak, 15ADC, 10Arms continuous, 30A peak non-continuous current
• Easy protect function at excessive input

Applications

• For use with 80000/90000 series
• Use N278xA current probe with N2779A power supply
• E2697A high impedance adapter
• For use with 90000 X-series
• Use the N5449A high impedance probe adapter

Certifications

• CAT I 300V
• CAT I

Specificaties
Kenmerk Waarde
Current 15A
Probe Type AC/DC
Minimum Bandwidth 0Hz
Maximum Bandwidth 100000kHz
Safety Category CAT I 300 V
Safety Category Level CAT I
Model Number p N2893A
Best Accuracy ±1% + 1 mV
Safety Category Voltage 300V
Bandwidth DC to 100 MHz
6 op voorraad - levertijd is 1 werkdag(en).
Prijs Each
3.719,00
(excl. BTW)
4.499,99
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 3.719,00
Related Products
Dual range a.c. current clamp nominal measuring ranges ...
Description:
Dual range a.c. current clamp nominal measuring ranges 0.1A to 20A a.c. and 0.5A to 200A a.c.Safe, non intrusive current measurement40Hz to 10kHz bandwidthErgonomic jaw design for measurement where access is difficult and allows 'hooking' onto the cableMax. conductor size ...
Dual range a.c. current clamp nominal measuring ranges ...
Description:
Dual range a.c. current clamp nominal measuring ranges 0.1A to 20A a.c. and 0.5A to 200A a.c.Safe, non intrusive current measurement40Hz to 10kHz bandwidthErgonomic jaw design for measurement where access is difficult and allows 'hooking' onto the cableMax. conductor size ...
Suitable for use with oscilloscopes, recorders and data ...
Description:
Suitable for use with oscilloscopes, recorders and data loggers a.c. coupled output (no d.c. offset) Voltage output of 3V full scale for each range Fits around conductors up to 160mm diameter Extended battery life and external power supply input Meets ...
The i30 may be used in conjunction with ...
Description:
The i30 may be used in conjunction with bench and portable oscilloscopes for accurate non-intrusive ac & dc current measurement.,Applications include: inverters, switch mode power supplies, industrial controllers, automotive leakage currents and other applications requiring accurate isolated current measurement. ...