A1220EUA-T Allegro Microsystems, Bipolar Hall Effect Sensor, 3-Pin SIP

Datasheets
Wetgeving en compliance
Conform
Productomschrijving

A1220/1/2/3 Chopper Stabilised Hall Effect Latches, Allegro Microsystems

The Allegro Microsystems A1220, A1221, A1222, and A1223 Hall-effect Latches include a voltage regulator, Hall voltage generator, small-signal amplifier, chopper stabilisation and Schmitt trigger. They are also short circuit protected open-drain output to sink up to 25 mA.

A south pole turns on the output and a north pole turns off the output.

The voltage regulator permits operation with supply voltages of 3 V to 24 V.

Available in two package styles; 3-pin SOT23W for surface-mounting and a three-pin ultra-mini SIP for through-hole mounting.

AEC-Q100 automotive qualified
Symmetrical latch switchpoints
Resistant to physical stress
Superior temperature stability
Output short circuit protection
Operation from unregulated supply down to 3 V
Reverse battery protection

Hall Effect Sensors, Allegro MicroSystems

Specificaties
Kenmerk Waarde
Magnetic Type Bipolar
Mounting Type Through Hole
Pin Count 3
Minimum Magnetic Sensor Release Point -40 Gs
Maximum Magnetic Sensor Operating Point 40 Gs
Minimum Operating Supply Voltage 3 V
Maximum Operating Supply Voltage 24 V
Length 4.09mm
Width 1.52mm
Height 3.02mm
Dimensions 4.09 x 1.52 x 3.02mm
Minimum Operating Temperature -40 °C
Maximum Operating Temperature +85 °C
Package Type SIP
Typical Magnetic Sensor Hysteresis 45 Gs
25 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
60 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each (In a Pack of 5)
1,224
(excl. BTW)
1,481
(incl. BTW)
Aantal stuks
Per stuk
Per pak*
5 - 20
€ 1,224
€ 6,12
25 - 95
€ 0,856
€ 4,28
100 - 245
€ 0,672
€ 3,36
250 - 495
€ 0,62
€ 3,10
500 +
€ 0,566
€ 2,83
*prijsindicatie
Verpakkingsopties
Related Products
The ATS468 is a true zero-speed gear tooth ...
Description:
The ATS468 is a true zero-speed gear tooth sensor IC consisting of an optimized Hall IC and a permanent magnet pellet configuration in a single overmolded package. The integrated circuit provides a manufacturer-friendly solution for digital gear tooth sensing applications. ...
The Allegro Microsystems A1120, A1121, A1122, A1123, and ...
Description:
The Allegro Microsystems A1120, A1121, A1122, A1123, and A1125 Hall-effect, unipolar switches are temperature-stable and stress-resistant sensor ICs. High temperature performance is made possible through dynamic offset cancellation, which reduces the residual offset voltage normally caused by device over-molding, ...
The A1391/2/3/5 family of linear Hall effect sensors ...
Description:
The A1391/2/3/5 family of linear Hall effect sensors provides a voltage output that is directly proportional to an applied magnetic field. The A139x minimise current consumption to less than 25 μA through the addition of a user-selectable sleep mode, perfect ...
The Allegro A1101/2/3/4 and A1106 Hall-effect switches are ...
Description:
The Allegro A1101/2/3/4 and A1106 Hall-effect switches are produced with BiCMOS technology enabling fast power-on time and low-noise operation. Device programming is performed after packaging, to ensure increased switch-point accuracy by eliminating offsets that could be induced by package stress.Unique ...