Megger MIT300, Insulation Tester 999MΩ CAT III 600 V

  • RS-stocknr. 516-7681
  • Fabrikantnummer MIT300-EN
  • Fabrikant Megger
Datasheets
Wetgeving en compliance
N.v.t.
Land van herkomst: GB
Productomschrijving

MIT 300 Series Insulation & Continuity Testers

A range of insulation testers that meet the relevant requirements of EN61557, BS7671, HD 384, IEC 364 and VDE 0413 for applications in all aspects of electrical contracting, building maintenance, testing, inspection and servicing.

20mm LCD display with true analogue response
Tough rubber armoured case with self contained display cover that locks away underneath the instrument during use
Designed to hang comfortably around the neck for hands-free, or for bench use
Automatic 200mA fast continuity test on connection to the circuit
Lead resistance nulling on continuity allows for use of fused test probes
Automatic discharge of circuit under test
Safety input terminal interlock - prevents unsafe connection of test leads
Intelligent Safety System - even if connected to a live circuit whilst on continuity setting the tester will remain safe and undamaged
Live voltage warning alerts the operator when a circuit voltage over 25V exists when insulation testing
Safety lockout prevents the test from operating when the circuit voltage is > 50V
Continuity check - prevents a continuity test or buzzer test on a live circuit
3 phase safe - will not be damaged if connected across phases
Locking test button
Meets the requirement of BS EN 61010-1 for safe connection to a 440V Installation Category III supply (600V Phase to Earth)
IP54

MIT310A

Moving coil display

MIT320 benefits from the following additional features:

Backlit display and range selection ideal for low light environment
Selectable insulation alarm limit for fast go - no go testing
Selectable continuity alarm limit for fast go - no go testing
Resistance measurement range to 1 MΩ
SP3 switched probe supplied for one handed operation
SP1000 illuminated switched probe with ultra-bright LED light available separately

Note

RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty

Supplied with

instructions, 2 wire test lead set with crocodile clips, 8 x AA alkaline batteries, neck strap & carry case.

Specificaties
Kenmerk Waarde
Tester Type Insulation & Continuity Tester
Minimum Test Voltage 250V
Maximum Test Voltage 500V dc
Maximum Insulation Resistance Measurement 999MΩ
Display Type LCD
Test Current 1mA
Battery Life 5000 5-Second Tests
Minimum Operating Temperature -10°C
Maximum Operating Temperature +60°C
Power Source Battery
Safety Category Level CAT III
Safety Category Voltage 600V
Safety Category CAT III 600 V
Length 203mm
Weight 980g
Model Number p MIT300
Plug Type Type G - British 3-pin
Height 78mm
Dimensions 203 x 148 x 78mm
Width 148mm
Battery Type AA
1 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
16 op voorraad - levertijd is 2 werkdag(en) (UK-voorraad)
Prijs Each
Was € 480,00
455,00
(excl. BTW)
550,55
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 455,00
Related Products
Test box designed to provide confirmation that electrical ...
Description:
Test box designed to provide confirmation that electrical installation testers continue to operate properly, and maintain their accuracy and consistency between calibrations. Tests the full range of a testers capability.Does not trip RCD protected circuits.Tests to regulations BS7671, BS EN61557 ...
A comprehensive PAT and Installation instrument verification system ...
Description:
A comprehensive PAT and Installation instrument verification system in one rugged, drop-proof enclosure. It allows on-going performance checks to be carried out on test equipment to ensure accurate measurement between calibration intervals. Tests verified: Earth Continuity, Insulation Resistance, RCD Trip ...
DET24C is a clamp-on ground resistance tester that ...
Description:
DET24C is a clamp-on ground resistance tester that set new standards in terms of access, performance, features, simplicity of operation and safety. The units are designed with flat core ends to prevent dirt build-up, ensuring measurement integrity and improved reliability ...
Chauvin Arnoux remote control probe P01102092A is an ...
Description:
Chauvin Arnoux remote control probe P01102092A is an accessory specially developed to make insulation tests in the field simpler and quicker. Insulation measurement can be triggered with a single press on the yellow buttonEquipped with a torch function which effectively ...