FTDI Chip, 3.3 V USB to UART Cable, C232HD-DDHSP-0

  • RS-stocknr. 751-1172
  • Fabrikantnummer C232HD-DDHSP-0
  • Fabrikant FTDI Chip
Datasheets
Wetgeving en compliance
Conform
Land van herkomst: CN
Productomschrijving

USB 2.0 Hi-Speed to MPSSE Cable, FTDI Chip

The USB 2.0 Hi-Speed to MPSSE cables contain a small internal electronic circuit board, utilising the FTDI FT232H, encapsulated into the USB connector end of the cable. This chip handles all the USB signalling and protocols. The cables provide a fast, simple way to connect devices with 3.3 or 5V digital interfaces to USB.

Based on the single chip USB Hi-Speed FT232H device
USB 2.0 Hi-Speed (480Mbits/Second) and Full Speed (12Mbits/Second) compatible
Entire USB protocol handled on the chip – No USB-specific firmware programming required
USB Type A connector for direct connection to a host or hub
USB bus powered
Fully assisted hardware or X-On / X-Off software handshaking
Synchronous Serial (MPSSE) data rates of up to 30Mbps on JTAG, SPI and I²C
1kByte receive and transmit buffers for high data throughput
Transmit and receive LED drive signals
Adjustable receive buffer timeout
Support for USB suspend and resume
Low operating and USB suspend current Low USB bandwidth consumption
UHCI / OHCI / EHCI host controller compatible
Operating temperature range: -40 to +85°C
Cable length: 1800mm
FTDI’s royalty-free D2XX drivers eliminate the requirement for USB driver development in most cases

FTDI Chip USB To UART Cable

The FTDI chip USB 2.0 high-speed to UART cable incorporates FTDI’s FT232H USB to UART interface IC device that handles all the USB signalling and protocols. The cable provides a fast and simple way to connect devices with 3.3V digital interfaces to USB. This cable contains a small internal electronic circuit board, utilising the FT232H, encapsulated into the USB connector end of the cable. It has a single pole, receptaclex10 end connector.

Features and Benefits

• Adjustable receive buffer timeout
• Asynchronous UART transfer data rate up to 12Mbaud
• Fully assisted hardware or X-On/X-Off software handshaking
• Low operating and USB suspend current
• Low USB bandwidth consumption
• Maximum output of 450mA at 5VDC on VCC
• Operating temperature ranges between -40°C and 85°C
• Receive and transmit buffers of 1kb for high data throughput
• Support for USB suspend and resume
• Ten core cable with length of 1.8m
• Transmit and receive LEDs
• UART interface support for 7 or 8 data bits,1 or 2 stop bits and odd/even/mark /space/no parity
• UHCI/OHCI/EHCI host controller compatible
• USB 2.0 Hi-Speed (480Mbps) and full speed (12Mbps) compatible
• USB bus powered
• USB Type A connector for direct connection to USB host or hub

Applications

• Electronic systems
• Prototyping platform for USB interface on
• Rapid USB integration into existing
• Set Top Box PC - USB interface
• Upgrading legacy peripherals to USB
• USB bar code readers
• USB digital camera interface
• USB hardware modems
• USB industrial control
• USB instrumentation
• USB Medical applications
• USB to RS232/RS422/RS485 converters
• USB wireless modems

Certifications

• CE
• FCC approved

Specificaties
Kenmerk Waarde
Interface Function USB to UART
Kit Classification Cable
Kit Name 3.3 V
113 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
901 op voorraad - levertijd is 2 werkdag(en) (UK-voorraad)
Prijs Each
39,00
(excl. BTW)
47,19
(incl. BTW)
Aantal stuks
Per stuk
1 - 9
€ 39,00
10 - 19
€ 37,06
20 - 49
€ 35,18
50 - 99
€ 33,99
100 +
€ 33,13
Related Products
The VNC2 is the second of FTDI’s Vinculum ...
Description:
The VNC2 is the second of FTDI’s Vinculum family of Embedded dual USB host controller devices. The VNC2 device provides USB Host interfacing capability for a variety of different USB device classes including support for BOMS (bulk only mass storage), ...
Designed to replace an existing DE9 connector, (male ...
Description:
Designed to replace an existing DE9 connector, (male or female) RS-232/TTL UART connection with a drop-in USB replacement connection. Miniaturised modules which closely resemble a DE9 connector for PCB mountingUSB mini-B socket connectorThe modules contain a USB-Serial bridge IC and ...
The HUB Interface Expansion Module for the Raspberry ...
Description:
The HUB Interface Expansion Module for the Raspberry Pi is ideal if you want to expand the number of downstream port interfaces on your Pi board.What does the HUB Interface Expansion Module feature?•Dual Channel USB/UART/245FIFO/SPI/I2C/JTAG/GPIO interface converter•USB 2.0 hub chip ...
The TTL-234X-5V-WE and TTL-234X-3V3-WE cables are both un-terminated, ...
Description:
The TTL-234X-5V-WE and TTL-234X-3V3-WE cables are both un-terminated, they are bare and tinned wires. The difference between the two cables is that the TTL-234X-5V-WE operates at +5V levels (signals and power supply) and the TTL-234X-3V3-WE operates at +3.3V levels (signals ...