Megger 1002-001 Loop Impedance Tester 2 Wire Test Lead Set, For Use With MIT 300 Series

  • RS-stocknr. 480-1778
  • Fabrikantnummer 1002-001
  • Fabrikant Megger
Datasheets
Wetgeving en compliance
N.v.t.
Land van herkomst: GB
Productomschrijving

MIT 300 Series Insulation & Continuity Testers

A range of insulation testers that meet the relevant requirements of EN61557, BS7671, HD 384, IEC 364 and VDE 0413 for applications in all aspects of electrical contracting, building maintenance, testing, inspection and servicing.

20mm LCD display with true analogue response
Tough rubber armoured case with self contained display cover that locks away underneath the instrument during use
Designed to hang comfortably around the neck for hands-free, or for bench use
Automatic 200mA fast continuity test on connection to the circuit
Lead resistance nulling on continuity allows for use of fused test probes
Automatic discharge of circuit under test
Safety input terminal interlock - prevents unsafe connection of test leads
Intelligent Safety System - even if connected to a live circuit whilst on continuity setting the tester will remain safe and undamaged
Live voltage warning alerts the operator when a circuit voltage over 25V exists when insulation testing
Safety lockout prevents the test from operating when the circuit voltage is > 50V
Continuity check - prevents a continuity test or buzzer test on a live circuit
3 phase safe - will not be damaged if connected across phases
Locking test button
Meets the requirement of BS EN 61010-1 for safe connection to a 440V Installation Category III supply (600V Phase to Earth)
IP54

MIT310A

Moving coil display

MIT320 benefits from the following additional features:

Backlit display and range selection ideal for low light environment
Selectable insulation alarm limit for fast go - no go testing
Selectable continuity alarm limit for fast go - no go testing
Resistance measurement range to 1 MΩ
SP3 switched probe supplied for one handed operation
SP1000 illuminated switched probe with ultra-bright LED light available separately

Note

RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty

Supplied with

instructions, 2 wire test lead set with crocodile clips, 8 x AA alkaline batteries, neck strap & carry case.

Megger Insulation Tester Leads

The Megger insulation tester lead is a set of two leads used for BM100 insulation and continuity tester. This tester is used as a replacement or spare test lead set. These leads have 4mm connector and can be used with a range of multimeters, clamp meters, insulation testers, multifunction testers & continuity testers. For insertion into a difficult application, it has an extremely thin width, the length of the test leads is approximately 120cm, and that of the finger probes is 9cm.
Supplied with:
instructions, 2 wire test lead set with crocodile clips, 8 x AA alkaline batteries, neck strap & carry case.

Features and Benefits


Double insulated for additional protection
• Red and Black Leads
• 4mm Right Angle Plugs on Instrument End
• 4mm Safety Probes and Croc Clips on Test End

Certifications


CAT III 1000 V

Specificaties
Kenmerk Waarde
Accessory Type 2 Wire Test Lead Set
For Use With MIT 300 Series
5 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
19 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
61,49
(excl. BTW)
74,40
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 61,49
Related Products
Kits for performing tests required by NF C ...
Description:
Kits for performing tests required by NF C 15-1001 DT-170 (differential controller)1 DT-300 (earth and continuity measuring device and extension cord)1 M-9955538 (diagnostic book 15-100)1 DT-500* (Insulation controller and connectors).
Type 44® wire & cable has widespread uses ...
Description:
Type 44® wire & cable has widespread uses where environmental conditions demand consistently reliable performance. This mechanically tough wire & cable is easy to handle and install. Dual wall construction Small size, lightweight Low smoke and corrosive gas generation Resistant ...
Type 44® wire & cable has widespread uses ...
Description:
Type 44® wire & cable has widespread uses where environmental conditions demand consistently reliable performance. This mechanically tough wire & cable is easy to handle and install. Dual wall construction Small size, lightweight Low smoke and corrosive gas generation Resistant ...
High voltage insulation tester ideal for testing high ...
Description:
High voltage insulation tester ideal for testing high voltage equipment including switchgear, motors, generators and cables. Meets requirements of IEEE 43-2000 Capacitance and leakage current measurement Resistance measurements up to 2TΩ (Fluke 1555)Ramp function for breakdown testingVoltage breakdown detection ...