F3S-TGR-N_R Magnetic Safety Switch, Stainless Steel, 24 V dc

  • RS-stocknr. 746-7334
  • Fabrikantnummer F3S-TGR-NSPR-21-05
  • Fabrikant Omron
Datasheets
Wetgeving en compliance
Conform
Land van herkomst: GB
Productomschrijving

F3S-TGR Non Contact Safety Switch

The F3S-TGR non contact safety switches are designed to interlock hinge, sliding or removable guard doors. Plastic and stainless steel switches are available, the latter are ideally suited to high hygiene demands in the food industry. The switches have a long sensing range to avoid false signals resulting from an ill aligned door, for example.

Non-contact equals no abrasion which means no particles
Excellent coverage of mechanical tolerances
Can operate behind stainless steel fittings
Screw hole covers

F3S-TGR-N_C Switch

Connect up to 3 switches in series
LED for easy diagnosis
Electronic output (potential-free optocoupler output)
IP67 protection

F3S-TGR-N_R Switch

Connect up to 6 switches in series
Reed contacts
IP67 protection

Note

Models F3S-TGR-N_C are coded.
Actuator is included.
For suitable controller see the G9SA or G9SB from Omron, or the NE1A DeviceNet system.

Standards

EN standards certified by TÜV Rheinland, EN 954-1, EN ISO 13849-1, EN 60204-1, EN/IEC 60947-5-3, UL 508, CSA C22.2, BS 5304, EN 1088-1 conformance.

Specificaties
Kenmerk Waarde
Supply Voltage 24 V dc
Safety Contacts 2NC/NO
Housing Material Stainless Steel
Connection Type 5m cable
Switch Type Rectangular
Terminal Type Pre-Wired
Series F3S-TGR-N_R
Switching Distance 22 mm
IP Rating IP67
Actuator Included Yes
Depth 13mm
Dimensions 50 x 25.5 x 13 mm
Length 50mm
Safety Category 4
Actuator Type Magnetic
Number of Approach Directions 2
Width 25.5mm
Sensor Principle Magnetic
3 op voorraad - levertijd is 2 werkdag(en).
Prijs Each
Was € 120,00
108,24
(excl. BTW)
130,97
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 108,24
Related Products
The SensaGuard Non-Contact Switch is PLe, SIL 3 ...
Description:
The SensaGuard Non-Contact Switch is PLe, SIL 3 and Cat 4 rated and is intended for use with sliding, hinge or lift-off machine guard doors. These safety switches are based on RFID (Radio Frequency IDentification) technology for coding and inductive ...
Smallest designActuation only possible with BPS260, available separatelyLeft-hand ...
Description:
Smallest designActuation only possible with BPS260, available separatelyLeft-hand or right-hand side versions for door-mountingControl category up to 4 to EN954-1IP67 protection Connector 8 mm, 6-pole, latching interlockingDimensions: L13 x W26 x H36 mm.
Just one safety switch is sufficient for applications ...
Description:
Just one safety switch is sufficient for applications up to Cat 4 of EN954-1 - saving on wiringPossible to provide protection against defeat in accordance with VDE 060 by concealing the installationSimplified installation and adjustmentFor use in EX area Category ...
The IN4000 inductive safety switch is used for ...
Description:
The IN4000 inductive safety switch is used for position monitoring and has an inductive sensor that is activated by metal (e.g. steel ST37), therefore it does not require a separate coded actuator. Due to the non-contact form of operation, this ...