Wago Connector for use with Profibus

  • RS-stocknr. 508-3987
  • Fabrikantnummer 750960
  • Fabrikant Wago
Datasheets
Wetgeving en compliance
Niet conform
Land van herkomst: DE
Productomschrijving

Wago Fieldbus Connector

The Wago Fieldbus connector is an innovation that links a PROFIBUS device to a PROFIBUS line. It has a Stecker 9-Pin D-sub male connector.
BUS connectors:
Rewireable bus interface connectors are suitable for Bitbus, CAN-Bus, Interbus-S (Fieldbus), and Profibus systems. Compact and high quality, the 9-pole sub-D housings are available in bus node or bus termination versions and are colour-coded for easy identification. Service nodes are also available for CAN-Bus and Profibus systems, allowing online programming and repair. Each interface comes with detailed assembly instructions and mounting accessories.
Available in versions with horizontal or vertical cable outlets
Fast and reliable connection via screw terminals on the PCB
Bus terminations include SMT termination resistors
Colour-coded bodies aid installation and repair
Safe ESD protection thanks to fully insulated housings
Supplied with reliable crimp strain relief

Features and Benefits

Two horizontal cable entries: one input and one output
Fast and maintenance‐free cage clamp connection can be held in the open position with the help of an actuation slide mechanism
Externally operable switch to activate and/or deactivate the network terminating resistor
Enables the quick, easy connection of incoming and outgoing bus lines
Baud rate: 12Mbps
Supply voltage: 4.75VDC to 5.25VDC
Operating temperature ranges between 0°C and 60°C

Certifications

IP20 rated
IEC 60068-2-6
cULus 508 approved
TUV certified
EN 60079-0
IEC 60079-0

Specificaties
Kenmerk Waarde
Accessory Type Connector
For Use With Profibus
8 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
37 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
33,70
(excl. BTW)
40,78
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
€ 33,70
5 - 9
€ 32,68
10 +
€ 31,34
Related Products
The Siemens Sematic ET 200SP B1 type base ...
Description:
The Siemens Sematic ET 200SP B1 type base unit BU20-P12+A0+4B has push-in terminals without auxiliary terminals has dimensions of 20mm x 117mm x 35mm. Conductor cross-section from 0.14mm² to 2.5mm².
The Millenium 3 is the latest generation in ...
Description:
The Millenium 3 is the latest generation in the Millenium series. Improvements over the Millenium 2 Plus include:. Sandwich communication extension for XD10/XB10 and XD26/XB26Exchange of input/output state with FBD programmingOnly compatible with Smart controllersPeriodic exchanges with max. 6 XN06 ...
Front connectors with single cores. The flexible connection ...
Description:
Front connectors with single cores. The flexible connection guarantees a fast and direct connectionfrom the input/output modules of the SIMATIC S7-300/400 to the individual elements within the cabinet. Pre-attached single cores to reduce the wiring effortThe core cross-sections of 0.5 ...
A 2 core cabe designed to connect AS-i ...
Description:
A 2 core cabe designed to connect AS-i devices. The yellow cable supplies 30Vdc power to sensors and transfwers data and the black cable can be used for 24Vdc actuators. A trapezoidal cross section is used to prevent polarity reversal. ...