Wago Connector for use with Profibus

  • RS-stocknr. 508-4003
  • Fabrikantnummer 750970
  • Fabrikant Wago
Datasheets
Wetgeving en compliance
Niet conform
Land van herkomst: DE
Productomschrijving

Wago Fieldbus Connector

The Wago Fieldbus connector is an innovation that links a PROFIBUS device to a PROFIBUS line. It has Stecker 9-Pin D-sub male and female connector.
BUS connectors
:
Rewireable bus interface connectors are suitable for Bitbus, CAN-Bus, Interbus-S (Fieldbus) and Profibus systems. Compact and high quality, the 9-pole sub-D housings are available in bus node or bus termination versions and are colour-coded for easy identification. Service nodes are also available for CAN-Bus and Profibus systems, allowing online programming and repair. Each interface comes with detailed assembly instructions and mounting accessories.
Available in versions with horizontal or vertical cable outlets
Fast and reliable connection via screw terminals on the PCB
Bus terminations include SMT termination resistors
Colour-coded bodies aid installation and repair
Safe ESD protection thanks to fully insulated housings
Supplied with reliable crimp strain relief

Features and Benefits

Two horizontal cable entries: one input and one output
Fast and maintenance‐free cage clamp connection can be held in the open position with the help of an actuation slide mechanism
Externally operable switch to activate and/or deactivate the network terminating resistor
PG interface
Enables the quick, easy connection of incoming and outgoing bus lines
Baud rate: up to 12Mbps
Supply voltage: 4.75VDC to 5.25V DC
Operating temperature ranges between 0°C and 60°C

Certifications

IP20 rated
UL 508 approved

Specificaties
Kenmerk Waarde
Accessory Type Connector
For Use With Profibus
25 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
27 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
35,50
(excl. BTW)
42,96
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
€ 35,50
5 - 9
€ 34,43
10 +
€ 33,01
Related Products
SIMATIC ET 200SP, Potential distributor module, PotDis-Base Unit ...
Description:
SIMATIC ET 200SP, Potential distributor module, PotDis-Base Unit PotDis-BU Typ P2, dark-coloured, 1 x P1-potential, 17 x P2-potential, Push-In terminals. P1-, P2- and AUX-rail bridged to left BU, Packaging Unit: 1 Piece, WxH: 15mm x 117mm.
The Siemens Sematic S7-1500, front connector with screw ...
Description:
The Siemens Sematic S7-1500, front connector with screw type connection has 40-pole for 35mm wide modules including 4 potential bridges, and cable ties. Dimensions 29.8mm x 130.5mm x 46mmWeight 123g.
The Siemens Sematic ET 200SP B1 type base ...
Description:
The Siemens Sematic ET 200SP B1 type base unit BU20-P12+A0+4B has push-in terminals without auxiliary terminals has dimensions of 20mm x 117mm x 35mm. Conductor cross-section from 0.14mm² to 2.5mm².
Mechanical modules to record power modulesTo mount upright ...
Description:
Mechanical modules to record power modulesTo mount upright wiring kit via self-constructing potential railsPositive interconnection technologyReplaceable terminal box, even from middle of station networkHigh data security with self-constructing shield coverage on the back-plane busOption to colour-code the ...