Keenserts M10 x 1.5 Threaded Insert Hand Tool

  • RS-stocknr. 668-4698
  • Fabrikantnummer KRTM10-01
  • Fabrikant Keenserts
Datasheets
Wetgeving en compliance
N.v.t.
Land van herkomst: DE
Productomschrijving

Keenserts Inserts


The range of KEENSERTS® installation tools ensure quick, easy and secure installation of each insert. Each tool has notches where the protruding insert keys fit to enable effective winding in of the insert. Once the insert is fully wound in, the tool can be pulled back and turned 45 degrees, so the keys are situated between the notches, and driven down through the threads of the parent material, mechanically locking it into place.

Drilling and tapping can be done without any specialist equipment, just standard drills and taps.

Manufactured from stainless steel
Suitable for use in alloys, light materials, steel and cast iron to increase the strength of the thread in these materials
In thread repair use, the defect thread can be replaced with the same nominal diameter
Significantly increases load capability in weaker materials
Special keys lock the Keensert into place eliminating rotation
Easy to install no special taps required and no tangs to remove
High resistance to torque out and pull out
Camloc Inserts & Tools available in lightweight & heavy duty versions

KEENSERTS® stainless steel inserts and studs provide strong, permanent metal threads in a range of metals, including ferrous and non-ferrous. The range includes stock numbers 668-4667, 668-4676, 668-4663, 668-4708, 668-4679, 668-4705, 668-4702, 668-4673, 668-4711

The range of KEENSERTS® installation tools ensure quick, easy and secure installation of each insert. Each tool has notches where the protruding insert keys fit to enable effective winding in of the insert. Once the insert is fully wound in, the tool can be pulled back and turned 45 degrees, so the keys are situated between the notches, and driven down through the threads of the parent material, mechanically locking it into place.
Drilling and tapping can be done without any specialist equipment, just standard drills and taps.
For a range of installation tools see stock numbers: 668-4685, 668-4724,668-4720, 668-4727, 668-4718, 668-4698, 668-4689, 668-4682, 668-4691

Specificaties
Kenmerk Waarde
Thread Size Range M10 x 1.5
3 op voorraad - levertijd is 1 werkdag(en).
Prijs Each
86,66
(excl. BTW)
104,86
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 86,66
Related Products
Will punch up to 3.5mm in mild and ...
Description:
Will punch up to 3.5mm in mild and stainless steel, fibreglass/plasticsSplit slugs fall free and cannot cling to draw studGreatly increased life expectancy compared to standard punchesAvailable in 16 sizes including Pg and ISO sizesUse size 1 draw bolt for ...
AMPLIMITE HDF-20 series low profile IDC All-Plastic d-sub ...
Description:
AMPLIMITE HDF-20 series low profile IDC All-Plastic d-sub connectors for round conductor flat ribbon cable. These AMPLIMITE HDF-20 series IDC All-Plastic d-sub ribbon cable connectors have pre-assembled black 94V-0 rated thermoplastic housings and covers, standard 3.05mm mounting holes and are ...
Glenair Series 801 Mighty Mouse connectors feature a ...
Description:
Glenair Series 801 Mighty Mouse connectors feature a double-start modified stub ACME mating thread for improved protection against cross threading damage. The Mighty Mouse connector shells are machined from Aluminium and feature fluorosilicone seals and rear grommet protection from water ...
This kit is used to recover and repair ...
Description:
This kit is used to recover and repair damaged threads.Kit contents: different lengths and dimensions of HELICOIL® plus threaded inserts, drill bits, HSS manual threads, manual pins, tang breakers.Green colour to check the thread is present after fitting.