Pilz 24 → 240 V ac/dc Safety Relay Single or Dual Channel With 3 Safety Contacts and 1 Auxilary Contact

  • RS-stocknr. 489-6350
  • Fabrikantnummer 777302
  • Fabrikant Pilz
Datasheets
Wetgeving en compliance
Conform
Land van herkomst: DE
Productomschrijving

PNOZX2.8P Safety Relay by PILZ

The PNOZX2.8P range of safety relays from PILZ offers you safety and performance of a top branded safety relay all in one. The PNOZX2.8P offers you different modes of operation such as single or dual channel switches. Suitable for several different applications which are listed below.

Features and benefits:

• DIN rail mounted with screw terminals
• LED display that offers you the following measures:
- Supply voltages
- Switch status
• Automatic reset
• Manual reset
• Detection of shorts across contacts or without
• Simple & fast wiring
• Looping through of potential is possible quite easily
• Maintenance free thanks to the defined clamping force (no need for regular retightening)

Safety features

• The unit will monitor and measure and look out for an open circuit. If the circuit does open, the unit will immediately switch itself off to prevent hazards

Applications

• Safety gate monitor
• Instantaneous E-STOP monitoring
• Limit switch
• Card reader
• Light beam device mon. Type 2 with t/p, Safe delay-on de-energ. timer

Technical safety parameters

• EN 60204-1
• EN 62061
• EN ISO 13849-1
• VDE 0113-1

How do Safety Relays work and what are they used for?

Safety Relays work by helping reduce unnecessary risk and hazard within your circuit. A typical circuit configuration may look like a production line where highly automated machinery works quickly, i.e. a production or packing line in a warehouse or factory. This line forms part of your 'circuit' and along that circuit you will have safety devices in place like emergency push buttons, safety curtains or pressure sensitive mats. To ensure complete safety in these environments, a safety relay can be added to your circuit to allow you full control and monitoring of your working environment. A safety relay will run regular checks down your circuit by sending pulses back and forth to confirm whether any (for example) wiring was implemented incorrectly or any welding has occurred along the circuit. Once the relay has detected this, it would then shut down the area by cutting off the power, until the fault can be determined and fixed. Most recent safety relays feature intuitive LED displays that will alert users to any faults, this is of course useful to prevent harm to users and also proactively engage in maintenance before any machinery is damaged beyond repair, so certain cost savings can be associated when using a safety relay.

Some safety relays have specific functions and only work with certain devices like E-STOPs, some work better with other devices like safety curtains. More than one safety relay can be used to give you total monitoring of your circuit, ensuring you and your employees safety.

What are the differences between a traditional 'relay' and a 'safety relay'?

A traditional relay will open and close your circuit and the switch devices down that line, however it will not monitor it in the same way a safety relay will and cannot automatically shut down specified areas to prevent harm to the machinery or workers. Safety relays are not prone to the same potential risks that traditional relays are and can be relied upon to monitor short circuit faults, ground faults or wire breakage. Offering a greater protection over their counterpart relays, they are specifically designed with your safety in mind.

How do you operate a Safety Relay?

You must first align and wire the safety relay into your line and follow the setup instructions provided (will vary per manufacturer). Follow the onscreen instructions of the LED parallel to your instructions to perform integration into your circuit line. Depending on what parameters you set will determine the function of the safety relay (i.e. you tell it to cut off certain areas after certain criteria have been met, or you opt for a circuit wide halt of the line).

Approvals

CE, cULus Listed, TÜV, KOSHA, CCC.

Unit Specifics:

24 → 240 V ac/dc supply voltage Width 22.5mm
Length 94mm
Depth 121mm

Specificaties
Kenmerk Waarde
Supply Voltage 24 → 240 V ac/dc
Number of Channels 1, 2
Auxiliary Contacts 1
Function Safety Switch/Interlock
Safety Contacts 3
Range PNOZ X
Terminal Type Screw
Width 22.5mm
Length 94mm
Depth 121mm
63 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
160 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
170,90
(excl. BTW)
206,79
(incl. BTW)
Aantal stuks
Per stuk
1 +
€ 170,90
Related Products
Safety relay for two-handed controlsDuring dangerous movements, the ...
Description:
Safety relay for two-handed controlsDuring dangerous movements, the relay requires the operator to keep both hands out of the danger zoneApplications: mechanical presses, hydraulic presses, safety control circuitsRemovable terminals with connection via spring terminalsDisplay LEDs for relay statusDIN rail ...
The PNOZ Sigma S4 series of Safety relay ...
Description:
The PNOZ Sigma S4 series of Safety relay by PILZ. Known for their reliability and durability, PILZ safety relays offer you second to none safety protection features to ensure you and your workplace stay safe. Specifically, the S4 series is ...
The P2HZ X1 series of Safety Relays by ...
Description:
The P2HZ X1 series of Safety Relays by PILZ offer you affordable and reliable feedback control loops, specifically designed to handle the monitoring of your external relays or contactors. • Specially designed for two handed control/operation. The P2HZ series will ...
Simple and effective safety monitoring has never been ...
Description:
Simple and effective safety monitoring has never been more crucial in today's highly automated world. Prevention is key to site safety, that's why Schneider Electric offers a Safety Relay in the form of the 'Preventa XPSAF' module that is second ...