Baumer M23 12-Pin 5m Female Cable & Connector for use with Sensors and Actuators

  • RS-stocknr. 481-7767
  • Fabrikantnummer Z 130.005
  • Fabrikant Baumer
Datasheets
Wetgeving en compliance
Conform
Land van herkomst: DE
Productomschrijving

SSI series Ø 58 mm multi-turn absolute Encoders

Resolution up to 8192 points / turn for 4096 turns
SSI synchronous series outputs.
Gray or binary code.
Electrical zero positioning.
Standard flange with 10 mm shaft.
Front fixing by screws or bracket support (optional).
Connection via supplied radial connector.
Shielded cable connected to the connector available as an option.
Small coders, efficient and robust.

Solid Shaft / Hollow Shaft Absolute Encoders

Application
An absolute encoder provides the ability to remember the exact position following any power interruption. There is also no need for synchronisation. This is one of the reasons why absolute encoders are used where a safety standard is required (i.e. robotics industry). Typical applications are for speed or position control circuits. The features for these encoders are:

+ A unique signal for each angular position
No need for initialisation (zero reference)
Immediately after power up or after an interruption of power the position is maintained
No need for a counter to process the signal

Construction
The electrical signal of the absolute encoder is directly related to the angle of the shaft. The mechanical angular position is sensed by non contact optical elements, therefore without wear. The output of an infrared diode is transmitted through a transparent code disc and a diaphragm. The light/dark pattern is converted to an electrical signal by an array of photo diodes. The same code occurs only once per revolution. This encoder is defined as a single turn encoder.

Output circuit

Types of Code
Any electronic code is made out of a combination of bits. Each bit is characterised by a Low (0) or a High (1) signal. The combination of a series of bits is called a binary word. Several binary words make a code.

Single Step Code - Only one bit on the parallel output changes state at any given time. There is no possibility of any concurrent state changes. Single step code is very versatile and can maintain accuracy even allowing for slight misalignments of the disc and scanning device
Gray Code - This is a single step code, most absolute encoders use this code
Multiple Step Codes - Natural binary code: This type of code is similar to the decimal system, except that there are only 1 and 0. Each bit, depending on its position in the binary word, has a definite value. 20 to 2n assigned

Specificaties
Kenmerk Waarde
Connection Type M23 12-Pin
Cable Length 5m
Accessory Type Cable & Connector
Connection Gender Female
For Use With Sensors and Actuators
1 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
4 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
56,92
(excl. BTW)
68,87
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
€ 56,92
5 - 9
€ 55,22
10 +
€ 52,93
Related Products
The FQ2 vision sensor family is set to ...
Description:
The FQ2 vision sensor family is set to redefine the vision sensor market, providing advanced inspection, code reading and verification only previously available in higher end vision systems. With over 100 camera options, the FQ2 provides users with the ultimate ...
Hollow shaft rotary encoders are especially suitable for ...
Description:
Hollow shaft rotary encoders are especially suitable for direct mounting on the drive shaft (12 mm)Minimal effort required for mountingTemperature and ageing compensationShort-circuit proof outputsPolarity protection for operating voltage inputFlange socket; order mating connector separately.
M12 panel mount connectors with a free end ...
Description:
M12 panel mount connectors with a free end set of wires for self termination to your desired application, presented in a variety of panel mount entry types PG9 and M16, with a selection of contact configurations and cable lengths. Screw ...
RKWT series M12 connectors feature an industry standard ...
Description:
RKWT series M12 connectors feature an industry standard 3, 4 or 5 pole female threaded connector with 90 degree configuration and O ring. Cord sets are available in a variety of lengths and cable materials to suit a wide range ...