10-2857, Double-Sided Stripboard Epoxy Glass 220 x 100 x 1.6mm DIN 41612 FR4

Datasheets
Wetgeving en compliance
Conform
Land van herkomst: GB
Productomschrijving

Double-Sided Microboards Non-PTH

The component side of the card features a colander ground plane which assists glitch free high speed operation by dissipating switching spikes.
This ground plane is solder resist coated and screen printed in yellow, except for the region of the 0V rails which align with the 0 Volt rails on the wiring side for simple through connection.

DIN Type Stripboards

Suitable for use with the KM6-II eurocard sub-rack systems

The double-sided microboards are designed for microprocessor applications where compatibility, flexibility, high density and screening are of prime importance. VCC rails and a VCC bus are provided but not connected, so that individual rails may be committed as required. 64//96-way DIN 41612 indirect edge connectors may be fitted at either end.
The 3U (100x160) and 6U (233.4x160) boards are available with plated through holes (pth) as an alternative to the standard types. These boards have the added advantage of linking the top with the bottom pads directly via the holes, thereby dispensing with the need to fit linking pins, etc. Also the integrity of the joint is improved as the solder forms round the component lead on both surfaces, in addition to flowing through the hole. This helps to produce a solid and reliable connection, which is very important in applications where a high degree of vibration may be encountered.
Eurocards are manufactured from either epoxy glass material (blue) to BS4584 Part 3 or 16, or SRBP (synthetic resin bonded paper) material to BS4584 Part 5. Card thickness is 1.6mm. Copper 305g/m2 (1oz/ft2). Holes 1.0mm (0.040in.) dia. are pre-drilled on a 2.54mm matrix and all cards can be used with indirect edge connectors to DIN41612 (see Connectors/Terminals) except SRBP stripboard.

Note

Single-sided microboards have the same wiring pattern as the double-sided types, but omit the ground plane and 0 Volt rails on the component side of the card.

Specificaties
Kenmerk Waarde
Base Material Epoxy Glass Fabric Laminate
Number of Sides 2
Dimensions 220 x 100 x 1.6mm
Hole Diameter 1mm
Hole Pitch 2.54 x 2.54mm
Connection DIN 41612
FR Material Grade FR4
Length 220mm
Thickness 1.6mm
Width 100mm
2 op voorraad - levertijd is 1 werkdag(en).
Prijs Each
46,17
(excl. BTW)
55,87
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
€ 46,17
5 - 9
€ 43,87
10 - 39
€ 41,55
40 +
€ 39,25
Related Products
Complies with military standard P 13949F M12 13949F. ...
Description:
Complies with military standard P 13949F M12 13949F. Professional quality boards with blue coloured positive resinFire resistance: UL 94-V0Board material Glass-Epoxy FR4.
Microtrak FR4 epoxy glass laminates are dip coated ...
Description:
Microtrak FR4 epoxy glass laminates are dip coated with a high resolution positive working Photoresist. The Photoresist contains a dye which gives a good contrast against the copper, allowing boards to be easily inspected at the developing stage. Panels are ...
Ideal for development and prototype work, Veroboard is ...
Description:
Ideal for development and prototype work, Veroboard is intended primarily for wiring discreet components, particularly in analogue circuits.It is also useful when there is a large number of buses or common signals.The basic principle of Veroboard entails arranging components so ...
HF Verocard for circuits with a critical assembly.Component ...
Description:
HF Verocard for circuits with a critical assembly.Component side fully laminated with etched holes. Maximum isolation through grounding of the lamination. For reliable HF, digital and analogue circuits34 parallel circuit tracks, each with 540 holesNumerical gridDIN 41612 connector receptacle.