Oscilloscope Probes

An oscilloscope is considered to be the most used instrument for electrical engineers who need to measure electrical characteristics of electronic devices but you also need at least one probe.
Things to consider when choosing probes
• Ensure the probe's input connector matches the connector on your scope
• Choose a probe whose input resistance and capacitance match the input resistance and capacitance of your scope - matching is critical for guaranteeing proper signal transfer and signal accuracy
The best approach, for matching a probe with a scope, is to first choose a probe whose capacitance is within the range of your scope and then fine-tune the probe's capacitance by adjusting its compensation network using the probe's trimmer capacitor.
The 1X probes are suitable for many low frequency applications. They typically offer the same input impedance of the oscilloscope which is normally 1 M Ohm. The most common type of probe with a built in attenuator gives an attenuation of ten, and it is known as a 10X oscilloscope probe
Types of probes
Passive probes are the most commonly used probes for taking measurements. They are easy to use, relatively inexpensive, and fairly rugged. Available in the following configurations:
• 1´: no attenuation
• 10´: factor-of-10 attenuation
• 100´: factor-of-100 attenuation
• 1000´: factor-of-1000 attenuation
Attenuation probes serve to multiply the voltage measurement range of the oscilloscope by using an internal resistor that, when used in conjunction with the input resistance of the scope, creates a voltage divider. Useful for the following reasons:
• It allows for the measurement of a signal that might exceed the limits of the oscilloscope.
• The attenuation circuitry results in higher resistance and lower capacitance, which is important for high-frequency measurements.
Active probes contain active components, such as FETs or amplifiers. Commonly used for taking high-speed measurements (>500 MHz) or on high-impedance circuits. One limitation is their limited voltage range.
Differential probes are popular for measuring high-frequency signals or signals of very low amplitude.
A current probe measures the electrical current flowing through a conductor.
Tips
• Always use an appropriate probe tip and/or probe tip adapter whenever possible
• Keep ground leads short

...
Lees meer Lees minder

Filters

21 - 40 van 204 producten worden weergegeven
Resultaten per pagina
Omschrijving Prijs Probe Type Attenuation Bandwidth Maximum Common Mode Input Voltage Connector Type Model Number p Number of Probes Safety Category Level Safety Category Voltage Series Safety Category Rise Time
RS-stocknr. 796-6702
FabrikantnummerP6015A
FabrikantTektronix
€ 2.260,00
Each
Aantal stuks
High Voltage 1:1000 75MHz 20kV - P6015A 1 - - - - 4ns
RS-stocknr. 725-6604
FabrikantnummerP6139B
FabrikantTektronix
€ 524,00
Each
Aantal stuks
Passive 1:10 500MHz - BNC P6139B - CAT II 300V - CAT II 300 V -
RS-stocknr. 518-0987
Fabrikantnummer99.00173
FabrikantMulti Contact
€ 70,08
1 Set
Set(s)
Passive 1:10 250MHz - BNC 99.00173 - CAT II, CAT III 600 V, 1000 V - CAT II 1000 V, CAT III 600 V 1.2ns
RS-stocknr. 825-1196
Fabrikantnummer68.9554-28
FabrikantMulti Contact
€ 58,70
1 Set
Set(s)
Passive 1:10 250MHz - BNC 68.9554-28 1 CAT III, CAT IV 600 V, 1000 V SET Isoprobe CAT III 1000 V, CAT IV 600 V -
RS-stocknr. 898-6741
FabrikantnummerTA043
FabrikantPico Technology
€ 559,00
Each
Aantal stuks
Active, Differential 1:10, 1:100 100MHz 700V - - 2 CAT III 500 Vrms, 700 V ac/dc - CAT III 700 V ac/dc, 500 Vrms 3.5ns
RS-stocknr. 796-6718
FabrikantnummerP6247
FabrikantTektronix
€ 5.550,00
Each
Aantal stuks
Differential 1:1, 1:10 1GHz 25V BNC P6247 1 - - - - 350ps
RS-stocknr. 733-6145
FabrikantnummerN2791A
€ 612,00
Each
Aantal stuks
Differential 1:10, 1:100 25MHz 700V BNC N2791A - CAT II 1000V ac N CAT II 1000 V ac 14ns
RS-stocknr. 716-7419
FabrikantnummerVPS420-R
FabrikantFluke
€ 250,00
Each
Aantal stuks
Passive 1:100 150MHz - - VPS420 R 1 CAT III 2000V ScopeMeter 190 CAT III 2000 V -
RS-stocknr. 734-5035
FabrikantnummerP5210A
FabrikantTektronix
€ 3.350,00
Each
Aantal stuks
Differential, Gripper, High Voltage 1:100, 1:1000 50MHz 5.6kV - P5210A - CAT I, CAT III 1000 V, 2300 V P52XXA CAT I 2300 V, CAT III 1000 V -
RS-stocknr. 898-6753
FabrikantnummerTA045
FabrikantPico Technology
€ 889,00
Each
Aantal stuks
Active, Differential 1:10 200MHz 60V - - 2 CAT I ±60V - CAT I ±60V -
RS-stocknr. 448-4351
Fabrikantnummer15120
FabrikantTestec
€ 503,93
Each
Aantal stuks
Active, Differential 1:100, 1:1000 100MHz 1kV BNC TT-SI 9110 - CAT III 1000 V ac, 1400 V ac/dc SI CAT III 1000 V ac, CAT III 1400 V 3.5ns
RS-stocknr. 702-7910
Fabrikantnummer11060A
€ 30,20
Each
Aantal stuks
Surface Mount Device - - - - 11060A - - - - - -
RS-stocknr. 733-6141
FabrikantnummerN2790A
€ 1.468,00
Each
Aantal stuks
Differential, High Voltage 1:50, 1:500 100MHz 1.4kV BNC N2790A - CAT II, CAT III 600 V, 1000 V N CAT II 1000 V, CAT III 600 V 3.5ns
RS-stocknr. 668-7161
FabrikantnummerTDP1500
FabrikantTektronix
€ 4.780,00
Each
Aantal stuks
Active, Differential 1:1, 1:10 1.5GHz 25V - TDP1500 - - - TDP - 265ps
RS-stocknr. 512-5019
FabrikantnummerMTX1032-B
FabrikantMetrix
€ 452,00
Each
Aantal stuks
Differential 1:1, 1:10, 1:100 30MHz - BNC MTX 1032-B 4 CAT I, CAT II, CAT III 600V - CAT I, CAT II, CAT III 600 V 11.7ns
RS-stocknr. 898-6747
FabrikantnummerTA042
FabrikantPico Technology
€ 519,00
Each
Aantal stuks
Active, Differential 1:100, 1:1000 100MHz 1kV - - 2 CAT III 1000 Vrms, 1400 V ac/dc - CAT III 1400 V ac/dc, 1000 Vrms 3.5ns
RS-stocknr. 224-1225
FabrikantnummerSI-9002
FabrikantTestec
€ 301,15
Each
Aantal stuks
Active, Differential 1:20, 1:200 25MHz 1kV - TT-SI 9002 - CAT III 1000 V ac, 1400 V ac/dc SI CAT III 1000 V ac, CAT III 1400 V 14ns
RS-stocknr. 672-1706
FabrikantnummerZS1000
FabrikantLeCroy
€ 1.130,00
Each
Aantal stuks
Active 1:10 1GHz - ProBus ZS1000 - - - ZS - -
RS-stocknr. 898-6750
FabrikantnummerTA044
FabrikantPico Technology
€ 779,00
Each
Aantal stuks
Active, Differential 1:100, 1:1000 70MHz 5kV - - 2 CAT I 2500 Vrms, 7000 V ac/dc - CAT I 7000 V ac/dc, 2500 Vrms 5ns
RS-stocknr. 726-0035
FabrikantnummerTPP0100
FabrikantTektronix
€ 55,00
Each
Aantal stuks
Passive 1:10 100MHz 300V BNC TPP0100 - CAT II 300V TPP CAT II 300 V -
Related Products
For design, validation, debugging and characterization of common ...
Description:
For design, validation, debugging and characterization of common high-speed serial bus designs including I2C, CAN/LIN, SPI, Serial ATA, Ethernet (GbE), USB 2.0, FireWire (1394b); signal integrity, jitter and timing analysis; manufacturing engineering and test. Accurate measurements for serial and digital ...
For high-speed switch mode power supply design; CAN/LIN ...
Description:
For high-speed switch mode power supply design; CAN/LIN bus design; high-speed digital design; digital design and characterization; manufacturing engineering test; research and development. ±42 V (DC + pk AC) differential input voltage 18 dB CMRR (at 250 MHz 50X attenuation) ...
High quality passive voltage probes suitable for use ...
Description:
High quality passive voltage probes suitable for use with Tektronix oscilloscopes or as general purpose replacements. Each probe features compensation trimmers to allow matching to instruments. Supplied complete with accessoriesRated voltage CAT II 300V rms, CAT I 400V rms.
The TPP1000 is a high-bandwidth, general-purpose probe that ...
Description:
The TPP1000 is a high-bandwidth, general-purpose probe that offers breakthrough specifications in its product class. The probe's exceptionally low capacitive loading limits adverse affects on circuits and is more forgiving of longer ground leads. And, with wide bandwidth, users can ...