FTDI Chip USB to UART Development Board for FT232RQ, MM232R

  • RS-stocknr. 406-562
  • Fabrikantnummer MM232R
  • Fabrikant FTDI Chip
Wetgeving en compliance

FTDI Chip USB To UART Development Board

The FTDI Chip USB to UART development board is a miniature kit that uses FTDI’s FT232RQ, which is the latest device to be added to FTDI’s range of USB UART interface integrated circuit devices. It is a USB to serial UART interface with optional clock generator output and with asynchronous and synchronous bit bang interface modes. The USB to serial interface designs uses the FT232RQ and have been further simplified by fully integrating the external EEPROM, clock circuit and USB resistors onto the device. Also, there is a unique number burnt into the device during manufacture and is readable over USB. This forms the basis of a security dongle, which can be used to protect customer application software from being copied.

Features and Benefits

• Entire USB protocol handled on the chip that is no USB-specific firmware programming required
• Fully assisted hardware or X-On/X-Off software handshaking
• Data transfer rates from 300 baud to 1Mbaud
• In-built support for event characters and line break condition
• Configurable CBUS I/O pins
• Auto transmit buffer control for RS485 applications
• Transmit and receive LED drive signals
• New 48MHz, 24MHz, 12MHz and 6MHz clock output signal options for driving external MCU or FPGA
• Receive and transmit buffers for high data throughput
• Adjustable receive buffer timeout
• Synchronous and asynchronous bit bang mode interface options with RD# and WR#
• New CBUS bit bang mode option
• Support for USB suspend and resume
• Integrated 1024-bit internal EEPROM for storing USB VID, PID, serial number and product description strings, and CBUS I/O configuration
• Support for bus powered, self powered and high power bus powered USB configurations
• Integrated 3.3V level converter for USB I/O
• High I/O pin output drive option
• Integrated USB resistors
• Integrated power-on-reset circuit
• UART signal inversion option
• USB bulk transfer mode.• Single supply operating voltage ranges between 3.3V and 5.25V
• Operating temperature ranges between -40°C and 85°C
• Pb-free


• USB to RS232/RS422/RS485 converters
• Upgrading legacy peripherals to USB
• Cellular and cordless phone USB data transfer cables and interfaces
• Interfacing MCU/PLD/FPGA based designs to USB
• USB audio and low bandwidth video data transfer
• PDA to USB data transfer
• USB smart card readers
• USB instrumentation
• USB industrial control
• USB MP3 player interface
• USB flash card reader/writers
• Set top box PC - USB interface
• USB digital camera interface
• USB hardware modems
• USB wireless modems
• USB bar code readers
• USB software/hardware encryption dongles
• USB medical field


• ANSI/ESD S20.20:2014
• BS EN 61340-5-1:2007

Kenmerk Waarde
Interface Function USB to UART
Kit Classification Development Board
Featured Device FT232RQ
31 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
78 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
(excl. BTW)
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
€ 16,00
5 - 9
€ 14,86
10 - 19
€ 13,85
20 +
€ 13,51
Related Products
The MikroElektronika MIKROE-2549 Opto Encoder Click is a ...
The MikroElektronika MIKROE-2549 Opto Encoder Click is a linear incremental optical sensor/encoder click, which can be used for the movement or rotation encoding. Encoders of this type are widely used for many applications which involve precise detection of the position, ...
The Click accessory modules plug into the MikroBUS ...
The Click accessory modules plug into the MikroBUS sockets in MikroElektronika microcontroller development boards. ETH Click features an ENC28J60, a 28-pin, 10Base-T stand-alone Ethernet Controller. ENC28J60, 10Base-T Ethernet ControllerMAC, PHY, 8KB buffer RAMSPI serial interfacePower supply: 3.3V.
EVB-USB2534BC-01 4-Port, USB 2.0 Hub Battery Charger Board ...
EVB-USB2534BC-01 4-Port, USB 2.0 Hub Battery Charger Board is a space saving, 4-layer, RoHs compliant board for battery charging using the USB2534. Simple migration of USB2512B designs is possible due to pin compatibility of the USB2534 with the USB2514B and ...
The ADM2682E is a 5kVrms Signal and Power ...
The ADM2682E is a 5kVrms Signal and Power Isolated RS-485 Transceiver with ±15kV ESD Protection. Convenient connections for power and signal through screw terminal blocksConfigurable as half duplex or full duplex 5V or 3.3V operationEasily configurable through jumper connectionsTest points ...