Matrix Board FR2 with 1.02mm Holes 2.54 x 2.54mm Pitch, 454.66 x 95.1mm

Datasheets
Wetgeving en compliance
Conform
Land van herkomst: GB
Productomschrijving

KM6 Veroboard® boards for DIN 41612 connectors

Single-sided boards combining the advantages of Veroboard, the flexibility of Eurocards and DIN 41612 connectors.
For wiring by wrapping applications, spacing of 3.81 on the double height boards keeps the board route aligned on the grid of the adjacent connectors.
Silk-screened component installation grid.
The cutter (stock number 543-535) allows rapid completion of a circuit by interrupting the copper tracks on request.

DIN Type Stripboards

Suitable for use with the KM6-II eurocard sub-rack systems

The double-sided microboards are designed for microprocessor applications where compatibility, flexibility, high density and screening are of prime importance. VCC rails and a VCC bus are provided but not connected, so that individual rails may be committed as required. 64//96-way DIN 41612 indirect edge connectors may be fitted at either end.
The 3U (100x160) and 6U (233.4x160) boards are available with plated through holes (pth) as an alternative to the standard types. These boards have the added advantage of linking the top with the bottom pads directly via the holes, thereby dispensing with the need to fit linking pins, etc. Also the integrity of the joint is improved as the solder forms round the component lead on both surfaces, in addition to flowing through the hole. This helps to produce a solid and reliable connection, which is very important in applications where a high degree of vibration may be encountered.
Eurocards are manufactured from either epoxy glass material (blue) to BS4584 Part 3 or 16, or SRBP (synthetic resin bonded paper) material to BS4584 Part 5. Card thickness is 1.6mm. Copper 305g/m2 (1oz/ft2). Holes 1.0mm (0.040in.) dia. are pre-drilled on a 2.54mm matrix and all cards can be used with indirect edge connectors to DIN41612 (see Connectors/Terminals) except SRBP stripboard.

Note

Single-sided microboards have the same wiring pattern as the double-sided types, but omit the ground plane and 0 Volt rails on the component side of the card.

Specificaties
Kenmerk Waarde
Hole Pitch 2.54 x 2.54mm
Dimensions 454.66 x 95.1mm
Length 454.66mm
Width 95.1mm
Base Material Synthetic Resin Bonded Paper
Hole Diameter 1.02mm
FR Material Grade FR2
7 op voorraad - levertijd is 1 werkdag(en).
Prijs Each
14,94
(excl. BTW)
18,08
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
€ 14,94
5 - 9
€ 13,46
10 - 39
€ 12,84
40 +
€ 12,41
Related Products
Matrix boards with 1mm holes on a 2.54mm ...
Description:
Matrix boards with 1mm holes on a 2.54mm pitch. Recommended for wire-wrapping applicationsEpoxy glass - CEM 301.6mm thick, copper-cladSingle sidedHole pitch 2.54mm (0.1in)Hole dia 1.0mm.
Completely drilled boards, designed for the development of ...
Description:
Completely drilled boards, designed for the development of prototypes of analogue circuits.Thanks to the use of APW plugs, these cards are very versatile and allow discreet components to be connected wire-to-wire, or enable plugs and wrap pins to be fitted. ...
Quadratic soldering islands reduce risk of lifting during ...
Description:
Quadratic soldering islands reduce risk of lifting during soldering. Simple connections to adjacent soldering islands can also be made. An earth screen on the component side provides maximum shielding. Plug connectors compliant with DIN 41612, types B and C up ...
Matrix boards with 1mm holes on a 2.54mm ...
Description:
Matrix boards with 1mm holes on a 2.54mm pitch. SRBP single sided square pad PCBsTrack gap 0.54mmNominal thickness 1.5mmHole pitch 2.54mm (0.1in)Hole dia 1.0mmCopper thickness 35μm.