Parallax Inc XBee USB RF Transceiver Adapter Board for XBee Modules

Datasheets
Wetgeving en compliance
Conform
Land van herkomst: US
Productomschrijving

XBee Adapter Boards

Adapter boards for interfacing an Xbee wireless module to a PC or microcontroller. The USB board provides an easy PC interface to configure XBee modules using the Digi X-CTU software.

RS Product Codes
781-3099 XBee USB Adapter Board
781-3092 XBee 5.0/3.3 V Adapter Board
781-3096 XBee 5.0/3.3 V SIP Adapter Board

Parallax Inc RF Transceiver Adapter Board

The Parallax Inc RF Transceiver Adapter Board comes in a partially assembled kit form and provides a cost-effective solution to interfacing a PC or microcontroller to any XBee or XBee Pro module. The PC connection can be used to configure the XBee Module through Digi's X-CTU software. This adapter board can provide an easy interface to the XBee or XBee Pro modules by converting the 2mm pin spacing to breadboard-friendly 0.100” spacing. The adapter board also provides a way to connect pluggable wires or solder connections and also provides mounting holes.

Features and Benefits

• 4 status indicator LEDs for Power, RSSI, Associate and mode (sleep/ON)
• Communication is between serial pass through and XBee module
• Converts XBee 2mm pin spacing to 0.100” pin spacing
• Includes mounting holes
• Operating temperature ranges between -40°C and +70°C
• Partially assembled kit form for flexible configuration
• Pin-out compatible with our other XBee Adapter boards
• Provides an easy interface for configuring an XBee Module via a PC
• Provides easy pluggable wire or solder connections

Certifications

• ANSI/ESD S20.20:2014
• BS EN 61340-5-1:2007

WPAN (IEEE 802.15.4) - Parallax

Specificaties
Kenmerk Waarde
RF Technology RF Transceiver
Kit Classification Adapter Board
For Use With XBee Modules
Kit Name XBee USB
14 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
123 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
26,80
(excl. BTW)
32,43
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
€ 26,80
5 - 9
€ 26,27
10 +
€ 25,75
Related Products
The LC234X module provides a low cost USB ...
Description:
The LC234X module provides a low cost USB to UART bridge using the FT234XD IC to transfer data at up to 3M Baud. Ideal for programming Arduino Pro, ESP modules etc., the pinouts follow the industry standard FTDI TTL cable ...
The Click accessory modules plug into the MikroBUS ...
Description:
The Click accessory modules plug into the MikroBUS sockets in MikroElektronika microcontroller development boards. ETH Click features an ENC28J60, a 28-pin, 10Base-T stand-alone Ethernet Controller. ENC28J60, 10Base-T Ethernet ControllerMAC, PHY, 8KB buffer RAMSPI serial interfacePower supply: 3.3V.
The ADM2682E is a 5kVrms Signal and Power ...
Description:
The ADM2682E is a 5kVrms Signal and Power Isolated RS-485 Transceiver with ±15kV ESD Protection. Convenient connections for power and signal through screw terminal blocksConfigurable as half duplex or full duplex 5V or 3.3V operationEasily configurable through jumper connectionsTest points ...
Two eRIC Arduino Shields which allow wireless communication ...
Description:
Two eRIC Arduino Shields which allow wireless communication between Arduino™ boards using proprietary LPRS easyRadio technology. This technology provides considerably greater range and lower power consumption than similar Wi-Fi or Bluetooth devices operating in the overcrowded 2.4GHz bands. An on-board ...