Oscilloscope Probes

An oscilloscope is considered to be the most used instrument for electrical engineers who need to measure electrical characteristics of electronic devices but you also need at least one probe.
Things to consider when choosing probes
• Ensure the probe's input connector matches the connector on your scope
• Choose a probe whose input resistance and capacitance match the input resistance and capacitance of your scope - matching is critical for guaranteeing proper signal transfer and signal accuracy
The best approach, for matching a probe with a scope, is to first choose a probe whose capacitance is within the range of your scope and then fine-tune the probe's capacitance by adjusting its compensation network using the probe's trimmer capacitor.
The 1X probes are suitable for many low frequency applications. They typically offer the same input impedance of the oscilloscope which is normally 1 M Ohm. The most common type of probe with a built in attenuator gives an attenuation of ten, and it is known as a 10X oscilloscope probe
Types of probes
Passive probes are the most commonly used probes for taking measurements. They are easy to use, relatively inexpensive, and fairly rugged. Available in the following configurations:
• 1´: no attenuation
• 10´: factor-of-10 attenuation
• 100´: factor-of-100 attenuation
• 1000´: factor-of-1000 attenuation
Attenuation probes serve to multiply the voltage measurement range of the oscilloscope by using an internal resistor that, when used in conjunction with the input resistance of the scope, creates a voltage divider. Useful for the following reasons:
• It allows for the measurement of a signal that might exceed the limits of the oscilloscope.
• The attenuation circuitry results in higher resistance and lower capacitance, which is important for high-frequency measurements.
Active probes contain active components, such as FETs or amplifiers. Commonly used for taking high-speed measurements (>500 MHz) or on high-impedance circuits. One limitation is their limited voltage range.
Differential probes are popular for measuring high-frequency signals or signals of very low amplitude.
A current probe measures the electrical current flowing through a conductor.
Tips
• Always use an appropriate probe tip and/or probe tip adapter whenever possible
• Keep ground leads short

...
Lees meer Lees minder

Filters

1 - 20 van 207 producten worden weergegeven
Resultaten per pagina
Omschrijving Prijs Probe Type Attenuation Bandwidth Maximum Common Mode Input Voltage Connector Type Model Number p Number of Probes Safety Category Level Safety Category Voltage Series Safety Category Rise Time
RS-stocknr. 512-6078
FabrikantnummerTT-SI 9010
FabrikantTestec
€ 805,33
Each
Aantal stuks
Active, Differential 1:100, 1:1000 70MHz 5kV BNC TT-SI 9010 - CAT I, CAT II 2500 V ac, 7000 V ac/dc SI CAT I 2500 V ac, CAT II 7000 V ac/dc 5ns
RS-stocknr. 724-0924
FabrikantnummerPP007-WS
FabrikantTeledyne LeCroy
€ 380,00
Each
Aantal stuks
Passive 1:10 500MHz 400V BNC PP007-WS - CAT I, CAT II 300 V, 400 V PP CAT I 400 V, CAT II 300 V -
RS-stocknr. 800-3004
FabrikantnummerTPP0051
FabrikantTektronix
€ 29,00
Each
Aantal stuks
Passive 1:10 50MHz - BNC TPP0051 1 CAT II 300V - CAT II 300 V 7ns
RS-stocknr. 825-1209
Fabrikantnummer68.9556-28
FabrikantStaubli
€ 98,01
1 Set
Set(s)
Passive 1:10 500MHz - BNC 68.9556-28 1 CAT III, CAT IV 600 V, 1000 V SET Isoprobe CAT III 1000 V, CAT IV 600 V -
RS-stocknr. 825-1206
Fabrikantnummer68.9557-28
FabrikantStaubli
€ 107,59
1 Set
Set(s)
Passive 1:10 300MHz - BNC 68.9557-28 1 CAT III, CAT IV 600 V, 1000 V SET Isoprobe CAT III 1000 V, CAT IV 600 V -
RS-stocknr. 744-2518
FabrikantnummerFluke VPS40-III
FabrikantFluke
€ 124,10
Each
Aantal stuks
Passive 1:10 40MHz - - VPS40-III 3 CAT II, CAT III 600 V, 1000 V 120 CAT II 1000 V, CAT III 600 V -
RS-stocknr. 224-1219
Fabrikantnummer15101
FabrikantTestec
€ 332,34
Each
Aantal stuks
Active, Differential 1:10, 1:100 25MHz 700V BNC TT-SI 9001 - CAT III 1000 V ac, 1400 V ac/dc SI CAT III 1000 V ac, CAT III 1400 V 14ns
RS-stocknr. 481-0823
FabrikantnummerP2220
FabrikantTektronix
€ 145,00
Each
Aantal stuks
Passive 1:1, 1:10 200MHz - - P2220 - CAT II 150 V, 300 V TPS2000 CAT II 15 V, CAT II 300 V -
RS-stocknr. 384-878
FabrikantnummerVPS210-R
FabrikantFluke
€ 227,00
Each
Aantal stuks
Passive 1:10 200MHz - - VPS210 5 CAT II, CAT III 30 V, 600 V, 1000 V ScopeMeter 190 CAT II 1000 V, CAT II 3 V, CAT III 600 V -
RS-stocknr. 898-6820
FabrikantnummerTA133
FabrikantPico Technology
€ 179,00
Each
Aantal stuks
Passive 1:10 500MHz - BNC - 1 CAT II - - - 700ps
RS-stocknr. 733-6139
FabrikantnummerN2795A
€ 1.103,00
Each
Aantal stuks
Active 1:10 1GHz - - N2795A - - - N - 350ps
RS-stocknr. 715-8733
FabrikantnummerTPP0101
FabrikantTektronix
€ 56,00
Each
Aantal stuks
Passive, Voltage 1:10 100MHz 300V BNC TPP0101 - CAT I, CAT II 300 V, 300 V ac, 400 V ac TPP CAT I 400 V ac, CAT II 300 V, CAT II 300 V ac 3.5ns
RS-stocknr. 518-0987
Fabrikantnummer99.00173
FabrikantStaubli
€ 75,72
1 Set
Set(s)
Passive 1:10 250MHz - BNC 99.00173 - CAT II, CAT III 600 V, 1000 V - CAT II 1000 V, CAT III 600 V 1.2ns
RS-stocknr. 209-7860
FabrikantnummerP6243
FabrikantTektronix
€ 2.420,00
Each
Aantal stuks
Active 1:10 1GHz - BNC P6243 - - - - - 350ps
RS-stocknr. 725-6604
FabrikantnummerP6139B
FabrikantTektronix
€ 529,00
Each
Aantal stuks
Passive 1:10 500MHz - BNC P6139B - CAT II 300V - CAT II 300 V -
RS-stocknr. 898-6741
FabrikantnummerTA043
FabrikantPico Technology
€ 559,00
Each
Aantal stuks
Active, Differential 1:10, 1:100 100MHz 700V - - 2 CAT III 500 Vrms, 700 V ac/dc - 500 Vrms, CAT III 700 V ac/dc 3.5ns
RS-stocknr. 919-5087
FabrikantnummerVPS41
FabrikantFluke
€ 163,00
Each
Aantal stuks
Passive 1:10 - - - - - - - - - -
RS-stocknr. 898-6788
FabrikantnummerTA112
FabrikantPico Technology
€ 839,00
Each
Aantal stuks
Active 1:10 1GHz 33V BNC - 2 - 20V - - -
RS-stocknr. 898-6744
FabrikantnummerTA041
FabrikantPico Technology
€ 319,00
Each
Aantal stuks
Active, Differential 1:10, 1:100 25MHz 700V - - 2 CAT III 700 Vrms, ±700 V - 700 Vrms, CAT III ±700 V -
RS-stocknr. 796-6702
FabrikantnummerP6015A
FabrikantTektronix
€ 2.710,00
Each
Aantal stuks
High Voltage 1:1000 75MHz 20kV - P6015A 1 - - - - 4ns
Related Products
For design, validation, debugging and characterization of common ...
Description:
For design, validation, debugging and characterization of common high-speed serial bus designs including I2C, CAN/LIN, SPI, Serial ATA, Ethernet (GbE), USB 2.0, FireWire (1394b); signal integrity, jitter and timing analysis; manufacturing engineering and test. Accurate measurements for serial and digital ...
For high-speed switch mode power supply design; CAN/LIN ...
Description:
For high-speed switch mode power supply design; CAN/LIN bus design; high-speed digital design; digital design and characterization; manufacturing engineering test; research and development. ±42 V (DC + pk AC) differential input voltage 18 dB CMRR (at 250 MHz 50X attenuation) ...
High quality passive voltage probes suitable for use ...
Description:
High quality passive voltage probes suitable for use with Tektronix oscilloscopes or as general purpose replacements. Each probe features compensation trimmers to allow matching to instruments. Supplied complete with accessoriesRated voltage CAT II 300V rms, CAT I 400V rms.
The TPP1000 is a high-bandwidth, general-purpose probe that ...
Description:
The TPP1000 is a high-bandwidth, general-purpose probe that offers breakthrough specifications in its product class. The probe's exceptionally low capacitive loading limits adverse affects on circuits and is more forgiving of longer ground leads. And, with wide bandwidth, users can ...