Schneider Electric Auxiliary Contact, 1 Contact, 1 CO, A9N, DIN Rail, 6 A, 250V, A9N26904

RS-stocknr.:: 272-7434
Fabrikantnummer:: A9N26904
Fabrikant:: Schneider Electric

Schneider Electric Auxiliary Contact, 1 Contact, 1 CO, A9N, DIN Rail, 6 A, 250V, A9N26904

Subtotaal (1 eenheid)*

€ 50,04

(excl. BTW)

€ 60,55

(incl. BTW)

GRATIS bezorging voor bestellingen van meer dan € 90,00

Op voorraad

6 stuk(s) klaar voor verzending
46 stuk(s) klaar voor verzending vanaf een andere locatie

Heeft u meer nodig? Klik op 'Controleer leverdata' voor extra voorraad en levertijden.

Aantal stuks	Per stuk
1 +	€ 50,04

*prijsindicatie

RS-stocknr.:: 272-7434
Fabrikantnummer:: A9N26904
Fabrikant:: Schneider Electric

Specificaties

Datasheets

Wetgeving en compliance

Productomschrijving

Zoek vergelijkbare producten door een of meer kenmerken te selecteren.

Alles selecteren	Attribuut	Waarde
	Merk	Schneider Electric
	Number of Contacts	1
	Product Type	Auxiliary Contact
	Normal State Configuration	1 CO
	Series	A9N
	Mount Type	DIN Rail
	Contact Current	6A
	Terminal Type	Screw Clamp
	Contact Voltage	250V
	Mounting Location	Left
	Minimum Operating Temperature	-25°C
	Rated Insulation Voltage Ui	500V
	Operational Current Ie	6A
	Maximum Operating Temperature	70°C
	Standards/Approvals	EN/IEC 60947-5-1 GB/T 14048.5

	Alles selecteren
	Merk Schneider Electric
	Number of Contacts 1
	Product Type Auxiliary Contact
	Normal State Configuration 1 CO
	Series A9N
	Mount Type DIN Rail
	Contact Current 6A
	Terminal Type Screw Clamp
	Contact Voltage 250V
	Mounting Location Left
	Minimum Operating Temperature -25°C
	Rated Insulation Voltage Ui 500V
	Operational Current Ie 6A
	Maximum Operating Temperature 70°C
	Standards/Approvals EN/IEC 60947-5-1 GB/T 14048.5

Land van herkomst:: BE

Schneider Electric A9N Series Auxiliary Contact, 6A Operational Current, 250V Contact Voltage - A9N26904

This auxiliary contact provides an add-on signalling contact for industrial control equipment, designed to clip onto DIN rails and Interface with circuit-breaker or contactor assemblies on the left side. It is intended to monitor switching status and feed control or indication circuits across low-voltage installations, working within typical automation and electrical distribution environments.

Features & Benefits

• 1CO contact composition for single-circuit status signalling
• Rated operational current up to 6A for broad load compatibility
• Screw clamp terminals allow secure bottom-entry wiring
• Rated insulation voltage 500V for enhanced dielectric separation
• Operates from -25 to 70 °C for wide ambient conditions
• Compact 9mm width saves panel space

Applications

• Suitable for status feedback on contactors in motor control panels
• Ideal for integration into distribution board auxiliary circuits
• Used with automation relays for machine safety interlocks
• Can be used for PLC input signalling in industrial control racks

What Terminal types and conductor sizes are supported for connections?

Bottom-entry screw clamps accept 0.5 to 2.5mm² single conductors or 1.5mm² flexible conductors, including ferruled cables, tightened to 1 N·m.

How does the contact perform across different voltages?

It carries 0.1 to 6A depending on voltage and type, supporting AC up to 250V and specified reduced current ratings at higher AC and DC voltages.

What mechanical mounting options exist for panel fitting?

The unit clips onto a DIN rail and locates on the left side of the host device to align with comb busbar and distribution Block arrangements.

Which environmental protections and standards apply?

It meets IP20 protection, pollution degree 3, and conforms to EN/IEC 60947-5-1 and equivalent standards for signal contacts.

What packaging or handling information is relevant for procurement?

It is supplied as a single-piece pack with larger cartons holding 12 and pallet quantities up to 108, each unit weighing approximately 37 g.