Teledyne LeCroy AP Series AP033 Oscilloscope Probe, Differential Type, 500 MHz, 100:1, 10:1, ProBus Connector

Bekijk alle Oscilloscope Probes

Subtotaal (1 eenheid)*

€ 11.301,36

(excl. BTW)

€ 13.674,65

(incl. BTW)

Add to Basket
selecteer of typ hoeveelheid
Op voorraad
  • 2 stuk(s) klaar voor verzending
Heeft u meer nodig? Klik op 'Controleer leverdata' voor extra voorraad en levertijden.
Aantal stuks
Per stuk
1 +€ 11.301,36

*prijsindicatie

RS-stocknr.:
223-0892
Artikelnummer Distrelec:
176-25-951
Fabrikantnummer:
AP033
Fabrikant:
Teledyne LeCroy
Zoek vergelijkbare producten door een of meer kenmerken te selecteren.
Alles selecteren

Merk

Teledyne LeCroy

Product Type

Oscilloscope Probe

Probe Type

Differential

Attenuation

100:1, 10:1

Bandwidth

500MHz

Maximum Common Mode Input Voltage

5V

Connector Type

ProBus

Model Number

AP033

Series

AP

Standards/Approvals

No

The Teledyne LeCroy Fully Integrated: With the ProBus™ interface, the AP033 becomes an integral part of the oscilloscope. The probe sensitivity and offset can be controlled from the oscilloscope front panel, the probe front panel, or by using remote control commands (GPIB or RS-232). Sensitivity, offset, input capacitance, and common mode voltage range are displayed on the oscilloscope screen. When used with a LeCroy digital oscilloscope, no external power supply is required.

Wide Dynamic Range: The AP033 provides a range of sensitivities from x10 gain to ÷10 attenuation (even ÷100 with plug-on attenuator) for diverse signals. The sensitivity can be adjusted continuously from 200 μV/div to 1 V/div, when used with a LeCroy oscilloscope.

The input capacitance is just 2 pF/side (1 pF differential) whenever the ÷10 ATTENUATION is selected. Deflection factors of 2 mV/div to 1 V/div can be obtained with only 2 pF/side input capacitance and ±50 V CMVR.

At high sensitivities, the x10 GAIN and the ÷1 ATTENUATION are selected. This produces 4 nV/√Hz input noise, ±5 V of common mode voltage range (CMVR), and ±400 mV of DC differential offset. At lower sensitivities, the x1 GAIN and ÷10 ATTENUATION are selected, resulting in ±50 V CMVR and ±4 V of differential offset.

The input capacitance is just 2 pF/side (1 pF differential) whenever the ÷10 ATTENUATION is selected. Deflection factors of 2 mV/div to 1 V/div can be obtained with only 2pF/side input capacitance and ±50 V CMVR

DC CMRR is greater than 10,000:1 (80 dB) in both ATTENUATION settings

OFFSET up/down buttons allow OFFSET control from the probe amplifier body. Momentarily holding both buttons will zero the OFFSET

A supplied AC coupling capacitor head (0.1 μF) allows operation with large common mode or differential DC inputs

The input attenuator automatically changes from ÷1 to ÷10 when too much common mode signal is sensed. This and a fast input protection circuit also serve to protect the input from potentially damaging signals. When the probe is removed from the oscilloscope or the power is turned off, the ÷10 ATTENUATION is automatically invoked, leaving the inputs protected when not in use

Gerelateerde Links