Ultimaker Nozzle Nozzle for use with Olsson Block, Ultimaker 2 0.25 mm
- RS-stocknr.:
- 110-1982
- Fabrikantnummer:
- OBN001
- Fabrikant:
- Ultimaker
Subtotaal (1 eenheid)*
€ 30,66
(excl. BTW)
€ 37,10
(incl. BTW)
GRATIS bezorging voor bestellingen van meer dan € 90,00
Laatste voorraad RS
- Laatste 41 stuk(s), klaar voor verzending vanaf een andere locatie
Aantal stuks | Per stuk |
|---|---|
| 1 + | € 30,66 |
*prijsindicatie
- RS-stocknr.:
- 110-1982
- Fabrikantnummer:
- OBN001
- Fabrikant:
- Ultimaker
Specificaties
Wetgeving en compliance
Productomschrijving
Zoek vergelijkbare producten door een of meer kenmerken te selecteren.
Alles selecteren | Attribuut | Waarde |
|---|---|---|
| Merk | Ultimaker | |
| Product Type | Nozzle | |
| Sub Type | Nozzle | |
| For Use With | Olsson Block, Ultimaker 2 | |
| Nozzle Material | Brass | |
| Nozzle Size | 0.25 mm | |
| Standards/Approvals | No | |
| Alles selecteren | ||
|---|---|---|
Merk Ultimaker | ||
Product Type Nozzle | ||
Sub Type Nozzle | ||
For Use With Olsson Block, Ultimaker 2 | ||
Nozzle Material Brass | ||
Nozzle Size 0.25 mm | ||
Standards/Approvals No | ||
Vrijgesteld
- Land van herkomst:
- NL
Ultimaker 2 Jet Nozzles
The Olsson block brass Jet nozzles have a special tip angle and shoulder width, they also have a special internal geometry with an angle less steep down to the nozzle hole. A special treatment applied inside also makes them slip more. You can print 3°C to 5°C lower because of this treatment, and is also useful for oozing and drips.
With these special nozzles, you can print faster, the plastic flows much more easier than in classic nozzles. You can also clean them efficiently with cold pulls (or atomic pulls). The geometry of the inside makes it easier to get rid of plastic so changing colours or filament type is done faster and safer.
Use the 0.25mm brass nozzle to print small detailed prints, it's an expert nozzle (RS 110-1982)
The 0.4mm (RS 110-1983) is the standard size for a lot of 3D printers
If you print in wood filaments, this brass nozzle of 0.8mm is perfect for the job (RS 110-1985)
Ultimaker Accessories
Note
This nozzle is compatible with M6 Threads, you can put it on the Ultimaker Original (the fan shroud must be modified) or any of the Ultimaker family that has the Olsson Block mounted.
Gerelateerde Links
- Ultimaker Nozzle Nozzle for use with Olsson Block, Ultimaker 2 0.6 mm
- Ultimaker Nozzle Nozzle for use with Ultimaker 2, Olsson Block 0.5 mm
- Ultimaker Nozzle Olsson Block Kit for use with Ultimaker 2
- Ultimaker Nozzle for use with Olsson Block, Ultimaker 2+ 0.8mm
- Ultimaker Nozzle for use with Ultimaker 2, Olsson Block 0.4 mm
- Ultimaker Print Head for use with Ultimaker 2+ / Olsson Block 0.25 mm 0.6 mm, 0.8 mm
- Ultimaker Print Head for use with Ultimaker 2+ / Olsson Block 0.6 mm
- Ultimaker Nozzle and Heater Block for use with Ultimaker 2 Ultimaker Go