Fluke I30S Current Clamp, 20 A DC Max, AC/DC Adapter, 20 A AC Max, Voltage Output

RS-stocknr.:: 645-1836
Artikelnummer Distrelec:: 176-12-682
Fabrikantnummer:: I30S
Fabrikant:: Fluke

Fluke I30S Current Clamp, 20 A DC Max, AC/DC Adapter, 20 A AC Max, Voltage Output

Subtotaal (1 eenheid)*

€ 956,00

(excl. BTW)

€ 1.156,76

(incl. BTW)

GRATIS bezorging voor bestellingen van meer dan € 90,00

Op voorraad

8 stuk(s) klaar voor verzending
6 stuk(s) klaar voor verzending vanaf een andere locatie

Heeft u meer nodig? Klik op 'Controleer leverdata' voor extra voorraad en levertijden.

Aantal stuks	Per stuk
1 +	€ 956,00

*prijsindicatie

RS-stocknr.:: 645-1836
Artikelnummer Distrelec:: 176-12-682
Fabrikantnummer:: I30S
Fabrikant:: Fluke

Specificaties

Datasheets

Wetgeving en compliance

Productomschrijving

Zoek vergelijkbare producten door een of meer kenmerken te selecteren.

Alles selecteren	Attribuut	Waarde
	Merk	Fluke
	Product Type	Current Clamp
	Adapter Type	AC/DC
	Maximum DC Current	20A
	Maximum AC Current	20A
	Accuracy	±1% + 2 mA
	Maximum Conductor Size	19mm
	Output Type	Voltage
	Cable Length	2m
	Connector Type	BNC
	Battery Type	Alkaline
	Battery Life	30h
	Minimum Operating Temperature	0°C
	Maximum Operating Temperature	50°C
	Model Number	I30S
	Standards/Approvals	IEC 61326-1
	Safety Category Voltage	300V
	Safety Category Level	CAT III

	Alles selecteren
	Merk Fluke
	Product Type Current Clamp
	Adapter Type AC/DC
	Maximum DC Current 20A
	Maximum AC Current 20A
	Accuracy ±1% + 2 mA
	Maximum Conductor Size 19mm
	Output Type Voltage
	Cable Length 2m
	Connector Type BNC
	Battery Type Alkaline
	Battery Life 30h
	Minimum Operating Temperature 0°C
	Maximum Operating Temperature 50°C
	Model Number I30S
	Standards/Approvals IEC 61326-1
	Safety Category Voltage 300V
	Safety Category Level CAT III

Vrijgesteld

Land van herkomst:: CN

Fluke Current Clamp, 30A Maximum DC Current, 20A Maximum AC Current - I30S

This current clamp measures both AC and DC currents using Hall-effect sensing for non-intrusive recordings with oscilloscopes and similar instruments, and is designed for field and bench use where isolation from the conductor is required.

Features and Benefits:

• 30mA-30A DC range delivers wide measurement capability for varied loads
• 30mA-20A AC rms range supports common mains and control circuits
• Output sensitivity 100mV/A provides direct voltage output to instruments
• Accuracy ±1% of reading ±2mA ensures precise measurement at 25°C
• Frequency response DC-100kHz enables high-frequency waveform capture
• 2m cable and safety BNC connector allow secure oscilloscope connections

Applications

• Suitable for waveform capture with oscilloscopes and recorders
• Used for troubleshooting DC motor and drive current anomalies
• Ideal for verifying control circuit currents up to 30A
• Can be used for high-frequency signal monitoring in power electronics
• Used with test instruments requiring voltage-output current probes

What power source does it require and how long does it last?

It uses a 9V alkaline IEC6LR61 battery and provides approximately 30 hours of operation with a low-battery indicator.

What conductor size will it accept?

The clamp opens to accommodate conductors up to 19mm diameter.

Which safety and electromagnetic standards apply to its use?

It meets IEC 61326-1 for EMC and is rated to CAT III 300V for working voltage limits.

How is output zero adjusted for baseline correction?

A manual thumbwheel on the body allows the user to zero the output prior to measurement.

What loading conditions should the measuring instrument present?

The output expects a load impedance greater than 100kΩ and less than or equal to 100pF.

Warning

Use of the probe on uninsulated conductors is limited to 300 V ac rms or dc and frequencies below 1 kHz.

Supplied with

Alkaline PP3 battery, 4mm shrouded plug adaptor and operator’s manual.